GEA Pharma Systems Release: Moisture Content on Display

Published: Feb 14, 2012

14 February, 2012 -- New, inline moisture sensor from GEA Pharma Systems … simple to install … easy to operate … fast pay back.

GEA Pharma Systems, in co-operation with NDC, has developed a new inline moisture sensor for pharmaceutical drying systems that drastically simplifies moisture measurement, saves processing time, avoids unnecessary operator contact with toxic compounds and helps ensure a top product quality.

The new moisture sensor, LHP-NDC 710e, which fits into a standard 2” port on the dryer, eliminates the need for complex chemical modelling techniques (chemometrics) to ascertain the moisture content of a product during the drying process. It extracts just the moisture content as a single piece of information and displays it simply for the operator. This speeds up the drying process and improves accuracy.

Using standard techniques, samples of dried powder must be taken manually from each batch of powder and tested off line in a laboratory to establish when the correct moisture contact has been achieved. This is time consuming, requires the dryer to be stopped and to wait while the test is performed, and runs the risk of the target moisture level being overshot producing a product that is too dry and difficult (or impossible) to handle efficiently. Validated systems are susceptible to many outside influences, such as atmospheric conditions, which means that the moisture level can vary even if the process itself is constant.

The new sensor from GEA Pharma Systems, however, shows a continuous display of the actual moisture content on a display screen as the product dries. This allows the operator to monitor precisely the actual moisture content and to stop the drying at exactly the right point. There is no need to wait for results, no chance of over-drying the product, and the operator never has to come in direct contact with the product.

In addition the standard technique only provides a snapshot of the condition of a limited amount of product (5-10grams). The in-line moisture sensor, however, is capable of monitoring the complete drying cycle. The total amount of analysed product during the process cycle is estimated to be more than 1000 grams. This will enable the operator to gain an understanding of the complete process cycle and so continuously improve the production process as well as anticipate unplanned events.

When first installing the LHP-NDC 710e it is necessary to perform a simple calibration exercise to compare the reading on the sensor to actual readings from laboratory tests. These need to be done for each product to be dried. Once the calibration line has been plotted for each product the instrument remembers the settings and continues to show accurate moisture levels for each product. As this is a display of the actual moisture level in the powder it is unaffected by atmospheric conditions or other variables.

The Lighthouse Probe™, also from GEA Pharma Systems, is particularly useful when working with wet or sticky products when it is essential to ensure a clear view of the product. Conventional windows can easily become fouled when processing these types of products. The Lighthouse Probe™ uses an in-line window wash to keep a clear view at all times. Further features are the in-line calibration as well as end-of-process full CIP (Clean-in-Place), which makes it suitable for use in a GMP environment.

Dr. Harald Stahl, Senior Pharmaceutical Technologist, with GEA Pharma Systems said that the time savings for each product batch could be very significant. “Every time a batch is tested manually it can take 10-15 minutes. Sometimes batches have to be tested more often. The real risk is that the final moisture content is too low. In this case it’s possible that the whole batch could be rejected. The new sensor avoids this problem and ensures that the target moisture content is achieved every time.”

The LHP-NDC 710e is simple to install and can be ready for calibration in just 20 minutes. It allows the moisture content of any powder product to be adjusted as required.

All editorial enquiries to:

Steve Jordan

The Words Workshop Ltd

26 Swanwick Lane, Broughton, Milton Keynes, MK10 9LD

Tel: +44 1908 695500



All business enquiries to:

Tomas Vermeire - Senior Process Technologist - Lighthouse Probe Product Manager

GEA Pharma Systems


Tel: +32 (0) 3 350 1258



About GEA Pharma Systems

GEA Pharma Systems unites the technologies of Aeromatic-Fielder™, Buck™, Collette™, Courtoy™, Diessel™, and Lyophil™ to provide advanced one-stop solutions for solid and liquid dosage processing to the global pharmaceutical industry.

Back to news